Cloning Instructions

- Start by cleaning and sterilizing EVERYTHING (trays/domes/scissors/razor blades).
- Soak rooting medium in R/O (reverse osmosis) water mixed with both of these products:
- Nature's Solution Compost Tea (1 cup per gallon of R/O water) (Root Soak
- KLN Rooting Hormone (2 teaspoons per gallon of R/O water) & Spray)
- Re-soak rooting medium in above solution every 5-8 days (pour any excess water out of tray).
**The trick is to let the grow medium dry out 5-8 days prior to re-soaking (approximately 75% dry). The clones will try to put out roots to find water
- Squeeze the excess water out of the rooting medium (coco plugs or Grodan blocks) and place the medium in tray.
- Keep PH between 5.4 and 6.4
- Take 8" long clones and place in a cutting tray submersed in room temperature R/O water (this is the safest way to cut a clone).
- Cut down the 8" long clone to 4"- 6" at a 45 degree angle underwater.
- Dip 4" - 6" long clone (1/2 inch deep) in one of the following Rooting Hormone.
- Clonex Gel
- Dip & Grow
- Rootech
- Wood's Rooting Compound
- Place clone 1" deep in one of the following grow tray medium.
- Coco Plugs
- Oasis Cubes/Wedges
- Grodan Blocks
- Cut all large fan leaves on the clone in half with sterile scissors.
- Spray clones immediately with the same mixture from LINE #2.
**Mist clones with this spray once every three days
- After spraying the clones, spray the humidity dome with the same mixture then place the dome over clones and keep the ventilation holes closed.
- Place clones in a dark or subdued light for 24 hours.
- After 24 hours, open (halfway) ONLY 1 ventilation hole and put a Dual Florescent Light (T-12) or a Single T-5 Light Fixture 1" - 2" over the humidity dome.
- Set light timer to 20 hours ON and 4 hours OFF.
- Place Heat Mat under the tray and set thermostat at 77 degrees (always keep clones 74-79 degrees).
- After 5 days, open (halfway) the 2nd ventilation hole.
- After 14 days, open (entire way) both ventilation holes.
- You should have rooted clones ready to transplant in 14-21 days.
- 24 hours prior to transplanting, prop open the humidity dome 1" - 3" to let air in to harden the clones off.

Tips for after Cloning

**When taking clones from clone tray, feed roots with 1/4 strength bloom nutrients for the first week (PPM should be 300 - 500 and PH should be 5.3 - 6.3).

Advanced Spraying for Veg - Flower

**All sprays should be mixed with 1 quart R/O water and a wetting agent (such as Coco-Wet, SM-90 or Dutch Master Saturator) to make plant sprays.

First Week of Veg: Spray rooted clones with 3/4 tsp. Canna Rhizotonic and3/4 tsp. Grotek Insta-Green. Spray once per day for 5 days.

Second Week of Veg: Spray plants with 1 tsp. Ful-Power Fulvic (Humic) Acid and 1/4 tsp. Dyna-Gro Foliage-Pro. Spray once every other day for 5 days.

Third Week of Veg: Spray plants with 1/4 tsp. Silicate and 1/4 tsp. Messenger (and 1 drop PH Down). Spray only once this week.

Fourth Week of Veg: Spray plants with 3/4 tsp. Canna Rhizotonic and 1/2 tsp. Spray-n-Grow. Spray only once this week.
**This is a good week to cut clones and trim plants before going into flowering

First Week of Flower: Spray plants with 4 tbsp. Dutch Master Max FX Flower and 3/4 tsp. Canna Rhizotonic. Spray only once this week.

Second Week of Flower: Spray plants with 1/4 tsp. Messenger and 1/2 cup Nature's Solution Tea. Spray only once this week.
**You should start to see small flowers now. The following will be your last spray.

Third Week of Flower: Spray plants with 1 tsp. Ful-Power Fulvic (Humic) Acid and 1 1/2tsp. Sray-n-Grow. Spray only once this week.

**If you wish to keep spraying plants in the flower stage, use Dutch Master Max FX Flower with a very fine misting spray only. Spray once per week.